QuickTreeâ„¢ Pixel MegaTree / 180 Degrees 12v

[Product Description Page]

[FAQ & Documentation Page]

Ryan's Pixel MegaTree
(Similar Design)

AlphaPix: How to setup controller and sequencing application

What's in the kit

HinksPix: How to setup controller and sequencing application

Product Features

Our QuickTree with the AlphaPix controller is fully assembled and tested by HolidayCoro, ready to run out of the box. If the following tree doesn't meet your requirements, see our other selections of pre-designed Pixel MegaTrees.

	180 Degrees of Coverage
Ideal Viewing Distance From Audience	Varies (see above)
Items Suitable for Display	Scrolling text, singing faces, animated graphics
Ease of Sequencing	Moderate - Uses Commonly Available 50 x 16 "CCR' Sequences for Christmas and Halloween
Pixel Counts
Total Pixel Nodes per Tree	800
Vertical Sections / Strings	16
Pixel Nodes per Section / String	50 Nodes
Pixel-To-Pixel Spacing	2.0, 2.5, 3.0 Inches
Tree Dimensions
Height (Pixel Area)	8.7, 11.2, 13.8 Feet
Height (Overall Maximum) Including 6 Inch gap at base	9.2, 11.7, 14.3 Feet
Width (Pixel Area)	4.5, 6.0, 6.6 Feet
Width - Top of Tree	7.5 Inches
Pixel Spacing - Top (Horizontal / Pixel-to-Pixel)	1.5 Inches
Pixel Spacing - Bottom (Horizontal / Pixel-to-Pixel)	6.0 , 8.0, 8.5 Inches
General
Power Injection Required / Cables per Strand	No / One Cable
Type of pixel used	8mm RGB LED with 12mm Body
Assembly
Controller - Pre-wired with power and cables	Ready2Run Assembled and Tested
Lights - Pre-wired with waterproof connections	Ready2Run Assembled and Tested
Lights / Nodes pre-installed into PixNode Strips	No Usually 30 to 60 Minutes
Overall erection time for entire tree (with assembled hardware)	Usually 60 Minutes
PC and Sequencing Setup	60 minutes to 2 Days Depending on Customer Skill
Additional Required Items (Sourced by Customer)
Center Pole - 1-3/8" Top Rail Tubing (Home Depot, Lowes, Menards)	One, 10 Foot Section (under 10' tall) Two, 10 Foot Sections (over 10' tall)
8 Inch to 12 Inch Galvanized Nail / Stakes	19
Tent Stake / Re-Bar or Similar (Depends on local soil and ground conditions)	3 for Low Wind Load Areas 4 for High Wind Load Areas
Guy Wires or Rope	3 for Low Wind Load Areas 4 for High Wind Load Areas
Sequencing Software	Works with 100% of all Holiday Sequencing Software on the market including: Light-o-Rama S4 / S5 xLights LightShow Pro Vixen 3
Computer / Show PC	Requires PC with Ethernet network port (nearly all have this) Type and power of PC depends on sequencing software selected by customer.

Assembly Instructions / Information:

For each tree, there is a roll of pixel strip that needs to be divided into 16 individual sections. We recommend counting out 62 holes (1 at the top for the topper connection, 50 for the pixels, 11 for additional gap at the bottom) and then using that "master" strip against the next length to cut each of the 16 sections. You should end up with a small amount of strip when complete. Here is a chart that shows the specific lengths for each tree type:

Height	Width	Hole to Holes Spacing	Total Length of Provided Mounting Strip	# of Strips	Length of Individual Strip	# of Holes per Individual Strip
8.5 Ft	4.5 Ft	2.0 Inches	175	16	10.5 Feet	62
10.8 Ft	5.0 Ft	2.5 Inches	212	16	13.0 Feet	62
12.5 Ft	6.5 Ft	3.0 Inches	250	16	15.5 Feet	62

Helpful Tips:

It is not necessary to fold over the mounting strip when sliding into the topper slots since this product ships with the thicker Extreme Strip.
You may or may not need the strain relief tabs at the bottom of the tree depending on your specific mounting method.
Be sure to leave enough space at the bottom of the tree to allow for snow, grass and non-flat lawns.

Average Rating: Average Rating: 5 of 5