|
|
|
|
.
Hands on with product (enclosure, wiring, mounting not included)
Troubleshooting DMX Signal Issues
|
|
|
|
|
|
|
|
|
|
|
|
|
Product Features
-
General Product Information
-
Basic / Dumb control over elements that use RGB lights that do not need individual control. Element examples would include:
- 30 DMX Channels / 10 RGB Channels
- DMX addressing:
-
DIP Switch addressable directly on board (1 to 512 channels)
-
See chart in our Knowledge Base
-
When controller does not have a DMX data stream on the input (not hooked up to a DMX output device), the controller can be configured to output a test/demo sequence.
-
Four mounting holes in board (.12” or 1/8”) – on each corner and two in the center
-
Great for use in centralized controller elements
- Angled screw connectors for output, each output clearly labelled with RGB output locations
- Dual power input screw terminals handles up to 30 amps of power
- Vertical CAT5 and XLR plugs allow inputs even in confined controller housings
-
LED Indicator for DMX signal input
- Red, Green and Blue LED Indicators for each output - allowing to test controller without lights connected to outputs
- Mounting inside water resistant enclosure using our optional mounting kit
- 500Hz PWM Refresh rate prevents "flashing" when lights are recorded on video
- Common Anode / Shared Positive / Switched Negative
- Compatibility
- All DMX512 output devices including:
-
Power / Signal / Wiring
-
DMX input (see our Knowledge Base for wiring details)
-
Protocol: DMX512/1990
-
Signalling System: RS-485
-
Connector: RJ45 Female
-
Wired to E1.11 standard
-
Pin 1 (White/Orange) - RS-485 Positive
-
Pin 2 (Solid Orange) - RS-485 Negative
-
Connector: XLR3 (3 PIN) Male
-
The standard for XLR3 pin connections to CAT5 cable is:
-
Power input
-
Voltage Range: 7 to 24v DC
-
Screw terminal (right side of board): Positive 12v marked “DC+”
-
Screw terminal (right side of board): Negative 12v marked “DC-”
- Test Modes
- Turn ON switch 10 to activate built-in sequences (switch 10 will make the controller respond to incoming DMX signal instead)
- Switches 1-9 OFF: Black/No Output
- Switch 1 ON: Red
- Switch 2 ON: Green
- Switch 3 ON: Blue
- Switch 4 ON: Yellow
- Switch 5 ON: Purple
- Switch 6 ON: White
- Switch 7 ON: Switch from static Red > Green > Blue > White > Off / Black >
- Switch 8 ON: Color mixing between different colors (color mixing or red, green blue)
- Switch 9 ON: Adjust the speed of mode 8
- Switch 10 ON: Turn on test mode
- See the video on this page for samples of test mode
- Signal (PWM) output:
- Up to 2 amps per DMX channel (24 watts @ 12v) / 6 amps per RGB channel output (72 watts @ 12v) OR 60 amps per controller total (720 watts @ 12v). Note - Any load over 60 amps requires two 350w power supplies
-
Screw terminals (top of board) - four screw terminals (two power supplies)
- Dimming Levels / Steps: 8 Bit / 256 (DMX Maximum)
-
Maximum RGB light examples
-
Note: These are estimates and do not account for long lengths of cable, differences in power requirements for other vendors RGB lights or other possible factors. You should confirm power consumption prior to hookup - see our Knowledge Base for more information.
|
Per RGB Channel
(3 DMX Channels)
|
Per Controller - Up To 10 RGB Channels
(30 DMX Channels)
|
|
100 Nodes
6,000mA or 6amps per RGB channel 60ma per node with white output
|
1,000 Nodes
60,000mA or 60amps per controller 60ma per node with white output
|
|
60 Modules
6,000mA or 6amps per RGB channel
100ma per module with white output
|
600 Modules
60,000mA or 60amps per controller 100ma per module with white output
|
RGB Dumb / Basic Strip
|
33 Feet / 10 Meters
6,000mA or 6amps per RGB channel
181ma per foot with white output
|
460 Feet
60,000mA or 60amps per controller 130ma per foot with white output
|
- Included, optional and customer supplied items
- Items included with this item/product/bundle:
- One DMX Controller
- DMX Switch setting instructions / chart
- Required items for operation:
- RGB lights (basic/dumb) – will not work with individually controlled pixel lights. See our FAQ page for information on how to determine how many RGB lights can be controlled from each controller.
- Power supply (see our FAQ page for information about how large of a power supply you will need for your project / element.)
- DMX signal source / dongle (see below)
- DMX generating software (see below)
- Optional items
- Mounting (screws, bolts, two sided tape or other) - see our mounting kit
- Customer supplied tools or items:
- Assembly Instructions: None (See video)
- Estimated assembly time: First unit: Varies / for DIY / Custom Projects
- Technical Specifications
- Color: None / Green Board with white silk screen
- Dimensions & Weight
- Complete product (overall)
- Per: .41 pounds (6.56 oz) / 1.85 grams
- Height: 3.19" / 81mm
- Width: 8.85" / 225mm
- Depth (thickness): 1.17" / 30mm
- Temperature Range
- Operation: 10 to 110 degrees Fahrenheit
- Storage: -20 to 140 degrees Fahrenheit
- Material Composition
- Case: None / Bare Board - Design for mounting into the CG-1500 Enclosure. See our mounting kit
- Wires: None – screw terminals for power connections
- County of Origin
- Materials/parts: China
- Assembly: China
- Design: China / USA
- Certifications & Approvals
- Underwriters Laboratories (UL) Certified/Recognised/Approved: No
- CE: No
- ROHS (Lead Free): No / Unknown or not certified
- Warranty & Support
-
Warranty period
-
365 days from date of purchase
- For complete information, see our warranty details.
-
Customization: Yes - minimum order of 200 units.
-
Product Revision history
- 05-Jun-17: Initial Release
-
Revision 1.0 board (mfg)
|
|
|
|
|
|
You might also be interested in... |
|
|
|